Selected as Construction Manager for New Parking Deck on MetroHealth’s Main Campus

Donley’s is pleased to announce that we have been selected
as the Construction Manager for MetroHealth’s new 1,500-car, open-deck parking
garage on its West 25th Street main campus in Cleveland.  “Donley’s has the experience and knowledge to undertake this important piece of MetroHealth’s transformation,” said Walter Jones, senior vice president of campus transformation at MetroHealth. “We have a track record of working successfully with each other and are looking forward to this next project.”

We are proud to be a part of MetroHealth’s campus transformation.


http://www.crainscleveland.com/article/20170727/NEWS/170729831/metrohealth-names-donleys-to-oversee-construction-for-main-campus




Portland Cement – Hazard Training (2 of 5) – Tool Box Talks

Portland cement is a light gray or white powder. When in contact with moisture in eyes or on skin, or when mixed with water, portland cement becomes highly caustic (pH > 12) and will damage or burn (as severely as third-degree) the eyes or skin.

SKIN CONTACT
(Acute) Exposure to dry portland cement may cause drying of the skin with consequent mild irritation or more significant effects attributable to aggravation of other conditions.

(Chronic) Dry portland cement coming in contact with wet skin or exposure to wet portland cement may cause more severe skin effects, including thickening, cracking or fissuring of the skin. Prolonged exposure can cause severe skin damage in the form of chemical (caustic) burns.

METHODS OF PROTECTION – Prevention is essential to avoiding potentially severe skin injury. Avoid contact with unhardened (wet) portland cement products. If contact occurs, promptly wash affected area with soap and water. Do not rely on barrier creams; barrier creams should not be used in place of gloves. Use impervious, abrasion- and alkali-resistant gloves, boots and protective clothing to protect the skin from prolonged contact with wet portland cement in plastic concrete, mortar or slurries. Provisions must be made to enable employees to clean or exchange equipment if it becomes ineffective or contaminated on the inside with portland cement while in use and to ensure that equipment is maintained in a sanitary and reliable condition when not in use.

FIRST AID – Wash skin with cool water and pH-neutral soap or a mild detergent. Seek medical treatment if irritation or inflammation develops or persists. Seek immediate medical treatment in the event of burns.

GOOD PRACTICES FOR SKIN CARE

  • Wash areas of the skin that come into contact with wet cement in clean, cool water. Use a pH-neutral or slightly acidic soap. Check with the soap supplier or manufacturer for information on the acidity and alkalinity of the soap.
  • Consider using a mildly acidic solution such as diluted vinegar or a buffering solution to neutralize caustic residues of cement on the skin.
  • Do not wash with abrasives or waterless hand cleaners, such as alcohol-based gels or citrus cleaners.
  • Avoid wearing watches and rings at work since wet cement can collect under such items.

Do not use lanolin, petroleum jelly, or other skin softening products. These substances can seal cement residue to the skin, increase the skin’s ability to absorb contaminants, and irritate the skin. Skin softening products also should not be used to treat cement burns.

SAFETY REMINDER – DISCOMFORT OR PAIN CANNOT BE RELIED UPTON TO ALERT A PERSON TO A HAZARDOUS SKIN EXPOSURE.

Focusing On Your Job/Pre-Task Planning

Over 80% of all workplace injury arises from worker behavior. We make mistakes, errors in judgment or
simply do not have our full attention on the job and something happens. There is also a tendency to get so
focused on getting the job done that we do not recognize the obvious.

A few years ago in the main shops there was an incident where a fairly new worker fell into a hole in the floor
and required several stitches in his leg. The opening was well flagged off and the whole affair seemed a
mystery. The post incident interview went something like this: So, you saw the caution tape? “Yes”. And you
do understand what caution tape means? “Oh, yes.” And you stepped over the caution tape and fell into the
hole? “Yes, that is pretty much what happened.” Either this guy was a complete moron or there was some
other explanation.

On further questioning, it turned out that he was on the end of a tag line at the time. He was so focused on
keeping the plate steady that the consequences of stepping over the caution tape did not register. At first
this seemed unbelievable. However, some recent research on workplace injury confirmed that focused
concentration on a task reduces the capacity to recognize obvious hazards. And a significant number of
workplace injuries result from this kind of inattention.

This applies directly to vehicle operation such as forklifts or even pickup trucks. There is a felt sense of
pressure to get something done, we are driving totally wrapped up in the job and do not even seen the
person walking in the path of travel. Every year there are countless incidents like this.

Are there pressures and intense focus in our jobs? You bet. But it is how we deal with the pressure, how we
handle the intense focus that is important. Now and again we have talked about the four second reset as a
way of attuning ourselves to the hazards around us. Sometimes all it takes is a big breath when we sit
behind the wheel of a vehicle. In truth, it is some conscious act of getting outside of the pressure or job
focus that prevents this type of incident. How we do this is our individual preference or way of psychologically
handling the job demands here.

There is an old story about a man who is riding a very fast horse. As he gallops past a bystander the person
shouts, “Where are you going in such a hurry?” The man answers, “I don’t know. Ask the horse.” The very
same situation happens with many of us at work. We get caught up in the busy day. Direct the horse once in
a while and you won’t ride over one of your co-workers or fall into a hole.

PRE-TASK PLANNING BASICS:
Pre-task Planning (STA) is a great way to focus your team. The STA is a living document that helps everyone
to focus on their tasks for the day. Here are a few things to keep in mind when using this tool:

  1. Everyone has input
  2. Done in your work area by individual crews
  3. Identify your task for the day
  4. Identify what hazards you see with those hazards no matter how trivial they may seem
  5. Identify other trades working around you and ask the question “Can I safely work around them?”
  6. Identify how to abate the hazards you identified by asking yourself “Do I have the right training,
    equipment and or material?”
  7. If you job task changes then start over with the STA and ask yourself these simple questions

The piece of paper you are writing the information down on will not save your life, but the focus you are
placing on your work will. We never know what we have prevented only what we didn’t prevent.

Portland Cement – Hazard Training (1 of 5) – Tool Box Talks

Portland cement is a light gray or white powder. When in contact with moisture in eyes or on skin, or when mixed with water, portland cement becomes highly caustic (pH > 12) and will damage or burn (as severely as third-degree) the eyes or skin.

The pH scale is logarithmic. That means each change of one in pH value is 10 times more acidic. Therefore, a substance with a pH of 2 is 1000 times more acidic than one with a pH of 5!

The pH values of some common substances are given in the table below.

It is important to know the pH of substances because they may be corrosive or react with incompatible materials. For example acids and bases should not be stored or used near each other as their accidental combination could generate a huge amount of heat and energy, possibly resulting in an explosion.

pH is also important to know in case you spill the material on your skin or eyes. Whenever a substance enters the eye, flush with water for 15 minutes and get prompt medical attention.

EYE CONTACT
(Acute/Chronic) Exposure to airborne dust may cause immediate or delayed irritation or inflammation of the cornea. Eye contact by larger amounts of dry powder or splashes of wet portland cement may cause effects ranging from moderate eye irritation to chemical burns and blindness.

METHODS OF PROTECTION – When engaged in activities where portland cement dust or wet portland cement or concrete could contact the eye, wear goggles or safety glasses with side-shields. In extremely dusty environments and unpredictable environments, wear unvented or indirectly vented goggles to avoid eye irritation or injury. Contact lenses should not be worn when working with portland cement or wet portland cement products.

FIRST AID – Immediately flush eye thoroughly with water. Continue flushing eye for at least 15 minutes, including under lids, to remove all particles. Call physician immediately.

SAFETY REMINDER – BASIC MATERIALS TEND TO CAUSE WORSE EYE DAMAGE AND ARE HARDER TO FLUSH OUT OF THE EYE TISSUES THAN ACIDIC MATERIALS.

Progress on The Standard Project

Check out our progress on The Standard project in Charlottesville, VA. The $3.8 million concrete project consists of apartments and a 6-level precast parking structure. Donley’s scope includes approximately 406,000 sq. ft. of slab finish area in 6 levels of steel construction.

DCG Project Win!

Congrats to Donley’s Concrete Group on a recent project win! Last month we were awarded the Virginia War Memorial concrete project in Richmond Va. The $4.8 million project starts in Sept 2017 and is part of the DVS office and parking expansion.

Lightning Strikes – Tool Box Talks

The average bolt of lightning carries over 100,000,000 volts and can reach out over 100 miles. According to the National Oceanic and Atmospheric Administration (NOAA), lightning is one of the leading weather-related causes of death and injury in the United States. It is estimated that the Earth id struck by lightning 100 times every second and the odds of being struck by lightning over your lifetime is 1 in 3,000. Thunderstorms and lightning are most likely to develop on hot, humid days and can be very dangerous is a person is outdoors without the proper protection.

WAYS LIGHTNING CAN KILL

  1. There are 5 ways in which lightning can severely injure or kill people or animals.
  2. A direct strike usually results in cardiac arrest and/or stoppage of breathing
    A side flash may occur when the body of a person provides an alternate or parallel path for the current. This means the person may be another way for the current to reach the ground. If the current passes through the head or heart, death may occur.
  3. Conducted current from a lightning flash may range from a tingling shock to a massive current diverted from a poorly grounded electric power pole through the wiring system.
  4. Step voltage radiates out through the ground from a struck tree or pole. This results in many livestock deaths every year.
  5. Fires, fallen trees, crushed cars. These are secondary effects. Injuries that occur from these are an
    indirect result of lightning.

PROTECTION DURING A LIGHTNING STORM
There are several things one can do if caught outdoors when a lightning storm strikes. Take shelter inside a building or car and close the windows and doors. Get off equipment immediately. Get out of the water if you are swimming or boating and get away from it. If boating stay low and avoid contact with the water.

Do not take refuge under any tall, isolated object, such as a tree. Standing under a group of trees shorter than others in the area is better than being in the open. Avoid electric fences, clothes lines, metal pipes, rails, telephone poles and any other conductor. Put down any object that might conduct electricity, such as a rake, hoe or shovel. If you are outside with no protection get to a low spot, make your body as low to the ground as possible but do not lay flat on the earth. Curl on your side or drop to your knees and bend forward putting your hands on your knees. If there is a group of people, spread out. If someone feels there hairs stand on end, it may mean lightning is about to strike.

Stay calm and keep low.

FIRST AID FOR LIGHTNING STRIKES
If someone is struck by lightning, they do not contain and electrical charge. Provide first aid immediately for any injury that is visible, and be prepared to provide CPR. Immediately call 9-1-1.

MISUNDERSTANDINGS & MISINFORMATION ABOUT LIGHTNING
Rubber-soled shoes provide absolutely no protection from lightning.

If you can hear thunder, you are within 10 miles of a storm and are within reach of lightning.

An automobile can offer protection by acting like a Faraday cage, provided that the occupants do not touch the metal of the care while inside.

Protecting Workers From The Effects Of Heat – Tool Box Talk

FACTORS LEADING TO HEAT STRESS

  • High temperature and humidity;
  • Direct sun or heat;
  • Limited air movement;
  • Physical exertion;
  • Poor physical condition;
  • Some medicines;
  • Inadequate tolerance for hot workplaces; and
  • Insufficient water intake can all lead to heat stress.

WHAT KIND OF HEAT DISORDERS AND HEALTH EFFECTS ARE POSSIBLE AND HOW SHOULD THEY BE TREATED?
Heat Stroke
is the most serious heat related disorder and occurs when the body’s temperature regulation fails and body temperature rises to critical levels. It is a medical emergency that may result in death. The primary signs and symptoms of heat stroke are confusion; irrational behavior; loss of consciousness; convulsions; a lack of sweating (usually); hot, dry skin; and an abnormally high body temperature. If a worker shows signs of possible heat stroke, professional medical treatment should be obtained immediately. Until professional medical treatment is available, the worker should be placed in a shady, cool area and the outer clothing should be removed. Douse the worker with cool water and circulate air to improve evaporative cooling. Provide the worker fluids (preferably water) as soon as possible.

Heat Exhaustion is only partly due to exhaustion; it is a result of the combination of excessive heat and dehydration. Signs and symptoms are headache, nausea, dizziness, weakness, thirst, and giddiness. Fainting or heat collapse is often associated with heat exhaustion. Workers suffering from heat exhaustion should be removed from the hot environment and given fluid replacement. They should also be encouraged to get adequate rest, and when possible, ice packs should be applied.

Heat Cramps are usually caused by performing hard physical labor in a hot environment. Heat cramps have been attributed to an electrolyte imbalance caused by sweating and are normally caused by the lack of water replenishment. It is imperative that workers in hot environments drink water every 15 to 20 minutes and also drink carbohydrate-electrolyte replacement liquids (e.g., sports drinks) to help minimize physiological disturbances during recovery.

ADMINISTRATIVE AND/OR WORK PRACTICE CONTROLS TO OFFSET HEAT EFFECTS

  • Acclimatize workers
  • Replace fluids
  • Reduce the physical demands
  • Provide recovery areas
  • Reschedule hot jobs for the cooler part of the day
  • Monitor workers

WHAT PERSONAL PROTECTIVE EQUIPMENT IS EFFECTIVE IN MINIMIZING HEAT STRESS?

  • Reflective clothing, worn as loosely as possible, can minimize heat stress hazards.
  • Wetted clothing, such as terry cloth coveralls or two-piece, whole-body cotton suits are another simple and inexpensive personal cooling technique. It is effective when reflective or other impermeable protective clothing is worn.
  • Water-cooled garments range from a hood, which cools only the head, to vests and “long johns,” which offer partial or complete body cooling. Use of this equipment requires a battery-driven circulating pump, liquid-ice coolant, and a container.

SAFETY REMINDER – STAY HYDRATED AND WATCH FOR THE SIGNS OF A PROBLEM